Is a Souvenir Fridge Magnet a Toy? Understanding GPSR vs. EN 71-1
Not automatically. A flat, printed souvenir magnet with no play value is normally treated as an ordinary consumer product under the General Product Safety Regulation (GPSR). A three-dimensional, child-appealing magnet that children are likely to play with can be a toy under the Toy Safety Directive 2009/48/EC. In that case EN 71-1 becomes the main technical route to compliance.
The outcome depends on design, marketing and foreseeable use. It does not depend on the word "souvenir", and it does not depend on a "not a toy" label printed on the pack.
Compliance files go wrong in both directions. Some businesses treat every magnet as a toy and pay for testing they may not need. Others declare a product "not a toy", skip the risk assessment, and discover later that the classification does not hold. This guide shows how the decision is made and what follows from it.
Law versus standard: what "GPSR vs. EN 71-1" really compares
The two names in the title sit on different levels, and mixing them up causes most of the confusion.
Binding EU law. The GPSR is Regulation (EU) 2023/988. It has applied since 13 December 2024 and replaced the old General Product Safety Directive. The Toy Safety Directive 2009/48/EC is the binding law for toys. It will be replaced by Regulation (EU) 2025/2509, which applies from 1 August 2030.
A technical standard. EN 71-1 is a European standard on the mechanical and physical properties of toys. A standard is not a law. EN 71-1 is, however, a harmonised standard under the Toy Safety Directive. A toy that complies with it is presumed to meet the essential safety requirements the standard covers.
Non-binding guidance. The Commission's guidance documents on toys explain how to apply the law. They reflect the view of the Commission's toy safety expert group. Only the Court of Justice of the EU can give an authoritative interpretation.
So the real question is which legal route applies: the toy route or the general consumer-product route. EN 71-1 is a tool on the toy route. It is not an alternative to the GPSR.
The two laws also overlap. The GPSR applies only where no specific Union provisions with the same safety objective exist, and for products under such provisions it covers only the aspects they leave open. Toys remain subject to parts of the GPSR, including its rules on online sales and the Safety Gate rapid alert system.
How EU law defines a toy
The Directive covers products designed or intended, whether or not exclusively, for use in play by children under 14 years of age. Four parts of that definition decide most cases.
"Designed or intended." Play value must be introduced by the manufacturer, since almost anything has some play value for a child. The manufacturer's stated purpose counts, but the Commission's explanatory guidance says reasonably foreseeable use prevails over the declared intended use. A manufacturer who labels a product as not a toy must be able to support that claim.
"Whether or not exclusively." A product can be a toy and have another function. The Commission's own example is a key ring with a teddy bear attached. A fridge magnet shaped like a bear has the same dual-function logic.
"Children under 14." The test is who the product is for and who will foreseeably use it, not who buys it.
Annex I exclusions. The Directive lists products that are not toys, including decorative objects for festivities and celebrations, and products for collectors that carry a visible and legible indication that they are intended for collectors aged 14 and above. The list is illustrative. A product missing from it, such as a souvenir, is not automatically a toy. It is assessed against the general definition.
What the Commission guidance says about souvenirs and fridge magnets
Two guidance documents matter here.
Guidance document No 4 covers grey-zone products. Its indicative criteria include where the product is sold (souvenir shops are named), who the packaging and advertising target, the price, and the size. No single criterion decides the case.
Guidance document No 20 covers decorative products and products for collectors. It treats souvenirs as a category to be classified case by case. The version published in 2021 includes a souvenirs annex. Toy indicators there are a design aimed at children, movable arms and soft filling. Non-toy indicators are fragile materials, appeal to adults, a relation to the place visited, and detail.
The same document contains the most direct statement on this topic. In its annex for other and dual-use products, a 3D-shaped refrigerator magnet with play value is listed as a toy, and refrigerator magnets for puzzles are listed as toys as well. A 2D refrigerator magnet with no play value is listed as not a toy.
The Commission published a revised version of Guidance No 20 in November 2024. Check the current annexes before you rely on any example above in your own file.
The guidance also makes a point many businesses miss. A manufacturer who marks a product "This is not a toy" acts against the Directive when the guidance indicates the product is a toy. The label does not change the classification.
A decorative product that is not a toy must still be safe for children who may come into contact with it. That duty now comes from the GPSR.
Five common souvenir magnets and where they tend to fall
These are illustrative readings of the guidance criteria, not rulings. Authorities decide on the facts of each product.
Flat printed or flexible-sheet magnets
A 2D magnet showing a city skyline, a photo or a slogan has low or no play value. It leans clearly towards a non-toy and the GPSR route.
Hard 3D resin or ceramic landmark pieces
These send mixed signals. The material is hard, the motif relates to the place visited, and the buyer is typically an adult, which are the non-toy indicators of the souvenirs annex. The same product is 3D-shaped, which is a toy indicator in the other-products annex. Sales channel, price, size and packaging usually decide. A detailed resin cathedral sold in a tourist gift shop sits differently from a chunky resin animal in a bag of twelve.
Cartoon animals, characters and food figures
A bright, low-priced, child-appealing 3D figure leans towards a toy, especially with child-oriented packaging or sold in a toy department. Dual function does not take it out of the toy definition.
Magnet sets, puzzles and letters
The guidance lists fridge magnets for puzzles as toys. Sets of letters, numbers or shapes that children can rearrange fit that logic.
Soft or plush magnets
Soft-filled, cuddly products are a toy indicator in the souvenirs annex. A plush figure with a magnet sewn in is closer to the key-ring example than to a decorative object.
Marketing, age grading and foreseeable use
Classification evidence builds up from many small choices. Authorities look at the whole product presentation.
Listing and packaging wording. A souvenir magnet listed as a "toy set" hands a regulator the argument. Cartoon packaging, children's imagery and age claims point the same way. Check titles, images and categories on marketplace listings, because those count as part of how you present the product.
Price and quantity. Cheap multipacks of figures resemble toys. Single, detailed, place-specific pieces resemble souvenirs.
Age warnings are not an escape route. The toy rules prohibit a warning, such as "not suitable for children under 36 months", when it conflicts with the intended use judged from the product's function, dimensions and characteristics. Under the GPSR, labelling on age suitability is one of the aspects assessed. It does not replace safe design.
Collector claims need substance. A "for collectors 14+" indication must be visible and legible to work under Annex I. It does not help a product that children are likely to play with.
Document the reasoning. Whatever you decide, record why. For a product that could be seen as a toy, the technical documentation should describe intended and foreseeable use.
If the magnet is a toy: the Toy Safety Directive and EN 71-1
A toy must not endanger users or third parties when used as intended or in a foreseeable way, bearing in mind how children behave. The manufacturer carries out a safety assessment and a conformity assessment, draws up an EU declaration of conformity and affixes the CE marking. The technical documentation and declaration are kept for ten years.
The toy must carry a type, batch, serial or model number, or another identifier. It must also bear the manufacturer's name and a single contact address on the toy or, where that is not possible, on the packaging or in an accompanying document. Instructions and safety information must be in a language easily understood by consumers in the Member State of sale. Warnings that influence the purchase decision must be visible before buying, including in online shops. Importers and distributors have their own checks, and an EU-established economic operator must be in place for a non-EU manufacturer.
The EN 71 series supports these duties. EN 71-1 covers mechanical and physical properties. EN 71-3 covers the migration of certain elements, which matters for painted and coated magnets. A manufacturer can depart from the harmonised standards, but the Commission's guidance says third-party EU-type examination by a notified body is then appropriate.
What EN 71-1 requires for magnets
The magnet clause targets ingestion. Swallowed magnets can attract each other across the intestinal wall and cause serious injury.
The core rule applies to loose magnets and magnetic components. Each must either have a magnetic flux index below 50 kG²mm² (0.5 T²mm²), or must not fit entirely inside the standard's small parts cylinder. The flux index is measured with a gauss meter under a defined test method.
The standard also applies to magnets that could be released during use. Toys are subjected to torque, tension, drop, impact and compression tests, and any magnet released afterwards falls under the same limits. This is the clause that matters for resin or ceramic figures with a magnet glued into the back. It is a test of how well the magnet stays in place.
EN 71-1 also prescribes warning wording for toys containing small magnets. Use the exact text of the edition you test against.
The standard's own rationale notes that known ingestion injuries involved powerful magnets, and that ceramic, rubberised and ferrite magnets have substantially lower attractive forces. Many fridge magnets use ferrite, often with decorative elements attached by adhesive. That is a reason to expect an easier test outcome. It is not an exemption. Compliance is shown by testing, and a neodymium insert in a 3D souvenir changes the picture entirely.
Other toy requirements apply too. Toys intended for children under 36 months may not have small parts that could detach, so a glued charm, bead or dome that comes loose in the drop or tension test becomes a choking hazard.
Note on editions: EN 71-1:2014+A1:2018 is the edition most compliance files cite, and standards catalogues now list a newer edition. Check which edition the Official Journal currently references before updating test reports.
If the magnet is not a toy: GPSR duties
"Not a toy" means a different route, not no route.
The GPSR requires that only safe consumer products are placed on the market. Its assessment criteria expressly include a product that is not designed or intended for children but is likely to be used by them, or that resembles an object commonly seen as appealing to children because of its design, packaging or characteristics. The Commission's guidance notice for businesses (C/2025/6233) gives child-appealing products as an example. Labelling on age suitability and the risk to vulnerable consumers such as children are listed as aspects to assess.
The manufacturer's duties follow. The manufacturer carries out an internal risk analysis and keeps technical documentation for ten years. The product carries a type, batch or serial number, or the packaging does if the product is too small. It carries the manufacturer's name and postal and electronic address, plus instructions and safety information in the language required by the Member State.
Where the manufacturer is outside the EU, a Responsible Person established in the EU must exist, and their name and contact details must appear on the product, packaging, parcel or accompanying document. Importers must indicate their own details. Distributors must verify that the required information is present before selling.
Online offers must show the manufacturer, the Responsible Person where applicable, product identification including an image, and any warnings or safety information. Accidents must be notified through the Safety Business Gateway, and marketplaces have their own obligations.
There is no CE marking under the GPSR. CE marking may only be affixed where EU legislation provides for it, so adding it "to be safe" to a non-toy magnet is a mistake.
The role of EN 71-1 under the GPSR
Nothing in the GPSR makes EN 71-1 mandatory for a non-toy product, and the GPSR sets no magnet-specific standard for non-toys. Whether to use EN 71-1's magnet criteria as a benchmark is a decision for the risk assessment. If the assessment shows children could access and swallow small magnets, the manufacturer needs a reasoned answer for how the design controls that hazard. Choosing a recognised test method is one way to build that answer. State it as a risk-assessment choice, not as a legal requirement.
Where classification typically goes wrong
A "toy" word in the listing title on a marketplace, for a product you argue is a decoration.
A "not a toy" stamp on a 3D, brightly coloured, low-priced figure.
The same design sold through a gift shop and a toy aisle, with one classification applied to both.
A "strong magnet" version with a loose neodymium insert, shipped with the same documentation as the weak ferrite version.
A collector-age marking on a product whose price, size and packaging say otherwise.
Relying on a supplier's "CE" or "EN 71 compliant" statement without a test report that matches the exact product you import.
Magnet-related alerts on the EU Safety Gate in 2024 and 2025 mostly concern toys with small, high-flux magnets, which shows where authorities are looking. It does not make souvenir magnets exempt.
A classification routine for importers and wholesalers
Check the exclusions. Does Annex I of the Directive apply, with its conditions?
Describe the product. Shape (2D or 3D), material, size, detail, play value, and how a child could foreseeably use it.
Look at the commercial presentation. Sales channel, packaging, price, quantity, listing text, age claims.
Review the magnet construction. Magnet type, dimensions, how it is fixed, and whether it can come loose.
Record the decision. Write down the route chosen and why, and revisit it when design, packaging or sales channels change.
Ask suppliers for construction photos, magnet type and dimensions, a flux index test report where relevant, drop and tension test results, the coating and paint material details, and the traceability marking they apply. A report on a similar item is not evidence for your specific product.
What is changing: Regulation (EU) 2025/2509
The new Toy Safety Regulation was published in the Official Journal on 12 December 2025. It applies generally from 1 August 2030 and repeals Directive 2009/48/EC on that date. Some web sources state 1 August 2026, which is incorrect. Toys placed on the market in line with the Directive before the application date may still be made available afterwards.
The definition of a toy stays the same in substance. Commentary on the final text also reports that decorative objects are excluded in Annex I only where they have no play value, and that the Commission can decide by implementing act whether specific products are toys. Confirm these points against the published text when you next revise your classification file.
Until 2030, the Directive and its harmonised standards remain the working framework.
FAQ
Does a souvenir fridge magnet need CE marking?
Only if it is a toy or falls under other CE-marked legislation. A non-toy magnet under the GPSR does not carry a CE marking.
Is EN 71-1 mandatory for fridge magnets?
Not as a standard on its own. For toys, compliance with it gives a presumption of conformity with the essential requirements it covers. For non-toys, it is at most a benchmark chosen in the risk assessment.
Does a non-EU manufacturer need an EU Responsible Person?
For a non-toy consumer product, yes. The Responsible Person must be established in the EU. For toys, an EU-established economic operator is required under the toy rules.
Can I write "not a toy" on the packaging?
You can, but it does not decide the classification. Commission guidance says reasonably foreseeable use prevails, and the label can be used against a product that the guidance treats as a toy.
Does the GPSR apply to toys?
In a complementary way. It covers aspects the toy law does not, and several parts, such as online sales and Safety Gate, apply to toys as well.
Bottom line
A souvenir fridge magnet is not a toy by default, and EN 71-1 does not apply to it by default. Classify the product on its design, presentation and foreseeable use, test the magnet construction honestly, and write the reasoning into the file. Then follow the route that classification opens: the Toy Safety Directive with CE marking, or the GPSR with a risk analysis, traceability and a Responsible Person.
Comments